APC IP DSLAM Guide de l'utilisateur Page 120
- Page / 603
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Application Note
112
7.2.3 How to Stack 2 units
• Eth0 enable (for uplink), its bridge port number is 385
• Eth1 disable (for downlink)
• MGMT interface disable
7.2.3.1 Scenario
PC 1
CPE
Unit 1
Ethernet
DSL
Ethernet
PC 3
Unit 2
CPE
DSL
Ethernet
PC 2
Ethernet
7.2.3.2 Configuration
Step1:
Step2:
Command Description
$get ethernet intf
Interface : eth-0
Type : Uplink UseDhcp : False
IP Address : 192.168.100.50 Mask :
255.255.255.0
Pkt Type : ALL
Orl(mbps) : 100
Configured Duplex : Auto Duplex : Full
Configured Speed : Auto
Class0thrshld : 100 Class1thrshld: 100
Verify the configuration after
stacking.
Command Description
( Master )
create ethernet intf ifname eth-0 ip 192.168.100.50 mask
255.255.255.0 enable
create bridge port intf portid 385 ifname eth-0 learning
disable status enable
create ethernet intf ifname eth-1 type downlink enable
create bridge port intf portid 386 ifname eth-1 learning enable
status enable
modify bridge mode enable
( Slave )
create ethernet intf ifname eth-0 ip 192.168.100.60 mask
255.255.255.0 enable
create bridge port intf portid 385 ifname eth-0 learning
disable status enable
create ethernet intf ifname eth-1 type downlink enable
create bridge port intf portid 386 ifname eth-1 learning enable
status enable
modify bridge mode enable
Master for unit 1
Slave for unit 2
IP is unnecessary for Downlink
port
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Produits connexes et manuels pour Mise en réseau APC IP DSLAM
Mise en réseau APC AP9630 Manuel d'utilisateur
(117 pages)
(117 pages)
Mise en réseau APC AP9224110 Spécifications
(16 pages)
(16 pages)
Mise en réseau APC AP9608 Spécifications
(9 pages)
(9 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels